为了造一套门禁系统，淘宝上搞来了一套RFID读卡器。
RC522，看上去是比较多的型号，哪家店都买得到。
本来想拔整个模块装进一个接线盒里，但是这尺寸刚刚好，如果放进去就没法盖盖子了。。。无奈，先裸奔。
Youtube连接：https://www.youtube.com/watch?v=4yIT7Gunn6c
也是网上找来的代码
#include <SPI.h>
#define uchar unsigned char
#define uint unsigned int//data array maxium length
#define MAX_LEN 16/////////////////////////////////////////////////////////////////////
//set the pin
/////////////////////////////////////////////////////////////////////
const int chipSelectPin = 10;
const int NRSTPD = 5;
//MF522 command bits
#define PCD_IDLE 0x00 //NO action; cancel current commands
#define PCD_AUTHENT 0x0E //verify password key
#define PCD_RECEIVE 0x08 //receive data
#define PCD_TRANSMIT 0x04 //send data
#define PCD_TRANSCEIVE 0x0C //send and receive data
#define PCD_RESETPHASE 0x0F //reset
#define PCD_CALCCRC 0x03 //CRC check and caculation//Mifare_One card command bits
#define PICC_REQIDL 0x26 //Search the cards that not into sleep mode in the antenna area
#define PICC_REQALL 0x52 //Search all the cards in the antenna area
#define PICC_ANTICOLL 0x93 //prevent conflict
#define PICC_SElECTTAG 0x93 //select card
#define PICC_AUTHENT1A 0x60 //verify A password key
#define PICC_AUTHENT1B 0x61 //verify B password key
#define PICC_READ 0x30 //read
#define PICC_WRITE 0xA0 //write
#define PICC_DECREMENT 0xC0 //deduct value
#define PICC_INCREMENT 0xC1 //charge up value
#define PICC_RESTORE 0xC2 //Restore data into buffer
#define PICC_TRANSFER 0xB0 //Save data into buffer
#define PICC_HALT 0x50 //sleep mode
//THe mistake code that return when communicate with MF522
#define MI_OK 0
#define MI_NOTAGERR 1
#define MI_ERR 2
//------------------MFRC522 register ---------------
//Page 0:Command and Status
#define Reserved00 0x00
#define CommandReg 0x01
#define CommIEnReg 0x02
#define DivlEnReg 0x03
#define CommIrqReg 0x04
#define DivIrqReg 0x05
#define ErrorReg 0x06
#define Status1Reg 0x07
#define Status2Reg 0x08
#define FIFODataReg 0x09
#define FIFOLevelReg 0x0A
#define WaterLevelReg 0x0B
#define ControlReg 0x0C
#define BitFramingReg 0x0D
#define CollReg 0x0E
#define Reserved01 0x0F
//Page 1:Command
#define Reserved10 0x10
#define ModeReg 0x11
#define TxModeReg 0x12
#define RxModeReg 0x13
#define TxControlReg 0x14
#define TxAutoReg 0x15
#define TxSelReg 0x16
#define RxSelReg 0x17
#define RxThresholdReg 0x18
#define DemodReg 0x19
#define Reserved11 0x1A
#define Reserved12 0x1B
#define MifareReg 0x1C
#define Reserved13 0x1D
#define Reserved14 0x1E
#define SerialSpeedReg 0x1F
//Page 2:CFG
#define Reserved20 0x20
#define CRCResultRegM 0x21
#define CRCResultRegL 0x22
#define Reserved21 0x23
#define ModWidthReg 0x24
#define Reserved22 0x25
#define RFCfgReg 0x26
#define GsNReg 0x27
#define CWGsPReg 0x28
#define ModGsPReg 0x29
#define TModeReg 0x2A
#define TPrescalerReg 0x2B
#define TReloadRegH 0x2C
#define TReloadRegL 0x2D
#define TCounterValueRegH 0x2E
#define TCounterValueRegL 0x2F
//Page 3:TestRegister
#define Reserved30 0x30
#define TestSel1Reg 0x31
#define TestSel2Reg 0x32
#define TestPinEnReg 0x33
#define TestPinValueReg 0x34
#define TestBusReg 0x35
#define AutoTestReg 0x36
#define VersionReg 0x37
#define AnalogTestReg 0x38
#define TestDAC1Reg 0x39
#define TestDAC2Reg 0x3A
#define TestADCReg 0x3B
#define Reserved31 0x3C
#define Reserved32 0x3D
#define Reserved33 0x3E
#define Reserved34 0x3F
//-----------------------------------------------//4 bytes Serial number of card, the 5 bytes is verfiy bytes
uchar serNum[5];int AUTHED_ID_NUM = 8;
unsigned char AUTHED_ID_LIST[][4] =
{
{0x72, 0xBB, 0x7C, 0x6F},
{0xF1, 0x6D, 0xB3, 0x85},
{0x09, 0x11, 0x8F, 0x87},
{0xCF, 0x9C, 0x24, 0x71},
{0x88, 0x04, 0xBF, 0xC5},
{0x88, 0x04, 0x5D, 0x9E},
{0x88, 0x04, 0xF6, 0x8A},
{0x88, 0x99, 0xA5, 0xCA}
};char *AUTHED_NAME_LIST[] =
{
"key-chain",
"white-card",
"Shanghai-transport",
"Beijing-transport",
"Guangzhou-Metro",
"Shenzhen-Metro",
"train-ticket #1",
"train-ticket #2"
};
void setup()
{
Serial.begin(57600);SPI.begin();
pinMode(chipSelectPin,OUTPUT); // Set digital pin 10 as OUTPUT to connect it to the RFID /ENABLE pin
digitalWrite(chipSelectPin, LOW); // Activate the RFID reader
pinMode(NRSTPD,OUTPUT); // Set digital pin 5 , Not Reset and Power-downMFRC522_Init();
pinMode(4, OUTPUT);
digitalWrite(4, LOW);
}void showCardDetail()
{uchar status;
uchar str[MAX_LEN];
// Show card type
ShowCardType(str);//Prevent conflict, return the 4 bytes Serial number of the card
status = MFRC522_Anticoll(str);// str[0..3]: serial number of the card
// str[4]: XOR checksum of the SN.
if (status == MI_OK)
{
Serial.print("The card's number is: ");
memcpy(serNum, str, 5);
ShowCardID(serNum);// Check people associated with card ID
uchar* id = serNum;
if( id[0]==0x4B && id[1]==0xE6 && id[2]==0xD1 && id[3]==0x3B ) {
Serial.println("Hello Mary!");
} else if(id[0]==0x3B && id[1]==0xE6 && id[2]==0xD1 && id[3]==0x3B) {
Serial.println("Hello Greg!");
}else{
Serial.println("Hello unkown guy!");
}
}}
unsigned long lastFoundTime = 0;
int lastFoundCard = -1;void loop()
{uchar status;
uchar str[MAX_LEN];
// Search card, return card types
status = MFRC522_Request(PICC_REQIDL, str);
if (status != MI_OK)
{
return;
}//showCardDetail();
status = MFRC522_Anticoll(str);
if (status == MI_OK)
{
memcpy(serNum, str, 5);
uchar* id = serNum;
int authedId = findInAuthedList(id);
if (authedId >= 0)
{
if (lastFoundCard != authedId || (millis() - lastFoundTime) > 2000)
{
Serial.print("Card read: ");
Serial.println(AUTHED_NAME_LIST[authedId]);
lastFoundTime = millis();
digitalWrite(4, HIGH);
delay(50);
digitalWrite(4, LOW);
}}
else
{
Serial.print("unknown card found: ");
ShowCardID(serNum);
}
lastFoundCard = authedId;
}MFRC522_Halt(); //command the card into sleep mode
delay(200);
}int findInAuthedList(uchar *id)
{
int i;
int j;
for (i=0; i<AUTHED_ID_NUM; ++i)
{
for (j=0; j<4; ++j)
{
if (AUTHED_ID_LIST[i][j] != id[j])
{
break;
}
}
if(j >= 4)
{
return i;
}
}
return -1;
}/*
* Function：ShowCardID
* Description：Show Card ID
* Input parameter：ID string
* Return：Null
*/
void ShowCardID(uchar *id)
{
int IDlen=4;
for(int i=0; i<IDlen; i++){
Serial.print(0x0F & (id[i]>>4), HEX);
Serial.print(0x0F & id[i],HEX);
}
Serial.println("");
}/*
* Function：ShowCardType
* Description：Show Card type
* Input parameter：Type string
* Return：Null
*/
void ShowCardType(uchar* type)
{
Serial.print("Card type: ");
if(type[0]==0x04&&type[1]==0x00)
Serial.println("MFOne-S50");
else if(type[0]==0x02&&type[1]==0x00)
Serial.println("MFOne-S70");
else if(type[0]==0x44&&type[1]==0x00)
Serial.println("MF-UltraLight");
else if(type[0]==0x08&&type[1]==0x00)
Serial.println("MF-Pro");
else if(type[0]==0x44&&type[1]==0x03)
Serial.println("MF Desire");
else
Serial.println("Unknown");
}/*
* Function：Write_MFRC5200
* Description：write a byte data into one register of MR RC522
* Input parameter：addr--register address；val--the value that need to write in
* Return：Null
*/
void Write_MFRC522(uchar addr, uchar val)
{
digitalWrite(chipSelectPin, LOW);//address format：0XXXXXX0
SPI.transfer((addr<<1)&0x7E);
SPI.transfer(val);digitalWrite(chipSelectPin, HIGH);
}
/*
* Function：Read_MFRC522
* Description：read a byte data into one register of MR RC522
* Input parameter：addr--register address
* Return：return the read value
*/
uchar Read_MFRC522(uchar addr)
{
uchar val;digitalWrite(chipSelectPin, LOW);
//address format：1XXXXXX0
SPI.transfer(((addr<<1)&0x7E) | 0x80);
val =SPI.transfer(0x00);digitalWrite(chipSelectPin, HIGH);
return val;
}/*
* Function：SetBitMask
* Description：set RC522 register bit
* Input parameter：reg--register address;mask--value
* Return：null
*/
void SetBitMask(uchar reg, uchar mask)
{
uchar tmp;
tmp = Read_MFRC522(reg);
Write_MFRC522(reg, tmp | mask); // set bit mask
}
/*
* Function：ClearBitMask
* Description：clear RC522 register bit
* Input parameter：reg--register address;mask--value
* Return：null
*/
void ClearBitMask(uchar reg, uchar mask)
{
uchar tmp;
tmp = Read_MFRC522(reg);
Write_MFRC522(reg, tmp & (~mask)); // clear bit mask
}
/*
* Function：AntennaOn
* Description：Turn on antenna, every time turn on or shut down antenna need at least 1ms delay
* Input parameter：null
* Return：null
*/
void AntennaOn(void)
{
uchar temp;temp = Read_MFRC522(TxControlReg);
if (!(temp & 0x03))
{
SetBitMask(TxControlReg, 0x03);
}
}
/*
* Function：AntennaOff
* Description：Turn off antenna, every time turn on or shut down antenna need at least 1ms delay
* Input parameter：null
* Return：null
*/
void AntennaOff(void)
{
ClearBitMask(TxControlReg, 0x03);
}
/*
* Function：ResetMFRC522
* Description： reset RC522
* Input parameter：null
* Return：null
*/
void MFRC522_Reset(void)
{
Write_MFRC522(CommandReg, PCD_RESETPHASE);
}
/*
* Function：InitMFRC522
* Description：initilize RC522
* Input parameter：null
* Return：null
*/
void MFRC522_Init(void)
{
digitalWrite(NRSTPD,HIGH);MFRC522_Reset();
//Timer: TPrescaler*TreloadVal/6.78MHz = 24ms
Write_MFRC522(TModeReg, 0x8D); //Tauto=1; f(Timer) = 6.78MHz/TPreScaler
Write_MFRC522(TPrescalerReg, 0x3E); //TModeReg[3..0] + TPrescalerReg
Write_MFRC522(TReloadRegL, 30);
Write_MFRC522(TReloadRegH, 0);Write_MFRC522(TxAutoReg, 0x40); //100%ASK
Write_MFRC522(ModeReg, 0x3D); //CRC initilizate value 0x6363 ???//ClearBitMask(Status2Reg, 0x08); //MFCrypto1On=0
//Write_MFRC522(RxSelReg, 0x86); //RxWait = RxSelReg[5..0]
//Write_MFRC522(RFCfgReg, 0x7F); //RxGain = 48dBAntennaOn(); //turn on antenna
}
/*
* Function：MFRC522_Request
* Description：Searching card, read card type
* Input parameter：reqMode--search methods，
* TagType--return card types
* 0x4400 = Mifare_UltraLight
* 0x0400 = Mifare_One(S50)
* 0x0200 = Mifare_One(S70)
* 0x0800 = Mifare_Pro(X)
* 0x4403 = Mifare_DESFire
* return：return MI_OK if successed
*/
uchar MFRC522_Request(uchar reqMode, uchar *TagType)
{
uchar status;
uint backBits; //the data bits that receivedWrite_MFRC522(BitFramingReg, 0x07); //TxLastBists = BitFramingReg[2..0] ???
TagType[0] = reqMode;
status = MFRC522_ToCard(PCD_TRANSCEIVE, TagType, 1, TagType, &backBits);if ((status != MI_OK) || (backBits != 0x10))
{
status = MI_ERR;
}return status;
}
/*
* Function：MFRC522_ToCard
* Description：communicate between RC522 and ISO14443
* Input parameter：command--MF522 command bits
* sendData--send data to card via rc522
* sendLen--send data length
* backData--the return data from card
* backLen--the length of return data
* return：return MI_OK if successed
*/
uchar MFRC522_ToCard(uchar command, uchar *sendData, uchar sendLen, uchar *backData, uint *backLen)
{
uchar status = MI_ERR;
uchar irqEn = 0x00;
uchar waitIRq = 0x00;
uchar lastBits;
uchar n;
uint i;switch (command)
{
case PCD_AUTHENT: //verify card password
{
irqEn = 0x12;
waitIRq = 0x10;
break;
}
case PCD_TRANSCEIVE: //send data in the FIFO
{
irqEn = 0x77;
waitIRq = 0x30;
break;
}
default:
break;
}Write_MFRC522(CommIEnReg, irqEn|0x80); //Allow interruption
ClearBitMask(CommIrqReg, 0x80); //Clear all the interrupt bits
SetBitMask(FIFOLevelReg, 0x80); //FlushBuffer=1, FIFO initilizateWrite_MFRC522(CommandReg, PCD_IDLE); //NO action;cancel current command ???
//write data into FIFO
for (i=0; i<sendLen; i++)
{
Write_MFRC522(FIFODataReg, sendData[i]);
}//procceed it
Write_MFRC522(CommandReg, command);
if (command == PCD_TRANSCEIVE)
{
SetBitMask(BitFramingReg, 0x80); //StartSend=1,transmission of data starts
}//waite receive data is finished
i = 2000; //i should adjust according the clock, the maxium the waiting time should be 25 ms???
do
{
//CommIrqReg[7..0]
//Set1 TxIRq RxIRq IdleIRq HiAlerIRq LoAlertIRq ErrIRq TimerIRq
n = Read_MFRC522(CommIrqReg);
i--;
}
while ((i!=0) && !(n&0x01) && !(n&waitIRq));ClearBitMask(BitFramingReg, 0x80); //StartSend=0
if (i != 0)
{
if(!(Read_MFRC522(ErrorReg) & 0x1B)) //BufferOvfl Collerr CRCErr ProtecolErr
{
status = MI_OK;
if (n & irqEn & 0x01)
{
status = MI_NOTAGERR; //??
}if (command == PCD_TRANSCEIVE)
{
n = Read_MFRC522(FIFOLevelReg);
lastBits = Read_MFRC522(ControlReg) & 0x07;
if (lastBits)
{
*backLen = (n-1)*8 + lastBits;
}
else
{
*backLen = n*8;
}if (n == 0)
{
n = 1;
}
if (n > MAX_LEN)
{
n = MAX_LEN;
}//read the data from FIFO
for (i=0; i<n; i++)
{
backData[i] = Read_MFRC522(FIFODataReg);
}
}
}
else
{
status = MI_ERR;
}}
//SetBitMask(ControlReg,0x80); //timer stops
//Write_MFRC522(CommandReg, PCD_IDLE);return status;
}
/*
* Function：MFRC522_Anticoll
* Description：Prevent conflict, read the card serial number
* Input parameter：serNum--return the 4 bytes card serial number, the 5th byte is recheck byte
* return：return MI_OK if successed
*/
uchar MFRC522_Anticoll(uchar *serNum)
{
uchar status;
uchar i;
uchar serNumCheck=0;
uint unLen;//ClearBitMask(Status2Reg, 0x08); //strSensclear
//ClearBitMask(CollReg,0x80); //ValuesAfterColl
Write_MFRC522(BitFramingReg, 0x00); //TxLastBists = BitFramingReg[2..0]serNum[0] = PICC_ANTICOLL;
serNum[1] = 0x20;
status = MFRC522_ToCard(PCD_TRANSCEIVE, serNum, 2, serNum, &unLen);if (status == MI_OK)
{
//Verify card serial number
for (i=0; i<4; i++)
{
serNumCheck ^= serNum[i];
}
if (serNumCheck != serNum[i])
{
status = MI_ERR;
}
}//SetBitMask(CollReg, 0x80); //ValuesAfterColl=1
return status;
}
/*
* Function：CalulateCRC
* Description：Use MF522 to caculate CRC
* Input parameter：pIndata--the CRC data need to be read，len--data length，pOutData-- the caculated result of CRC
* return：Null
*/
void CalulateCRC(uchar *pIndata, uchar len, uchar *pOutData)
{
uchar i, n;ClearBitMask(DivIrqReg, 0x04); //CRCIrq = 0
SetBitMask(FIFOLevelReg, 0x80); //Clear FIFO pointer
//Write_MFRC522(CommandReg, PCD_IDLE);//Write data into FIFO
for (i=0; i<len; i++)
{
Write_MFRC522(FIFODataReg, *(pIndata+i));
}
Write_MFRC522(CommandReg, PCD_CALCCRC);//waite CRC caculation to finish
i = 0xFF;
do
{
n = Read_MFRC522(DivIrqReg);
i--;
}
while ((i!=0) && !(n&0x04)); //CRCIrq = 1//read CRC caculation result
pOutData[0] = Read_MFRC522(CRCResultRegL);
pOutData[1] = Read_MFRC522(CRCResultRegM);
}
/*
* Function：MFRC522_Write
* Description：write block data
* Input parameters：blockAddr--block address;writeData--Write 16 bytes data into block
* return：return MI_OK if successed
*/
uchar MFRC522_Write(uchar blockAddr, uchar *writeData)
{
uchar status;
uint recvBits;
uchar i;
uchar buff[18];buff[0] = PICC_WRITE;
buff[1] = blockAddr;
CalulateCRC(buff, 2, &buff[2]);
status = MFRC522_ToCard(PCD_TRANSCEIVE, buff, 4, buff, &recvBits);if ((status != MI_OK) || (recvBits != 4) || ((buff[0] & 0x0F) != 0x0A))
{
status = MI_ERR;
}if (status == MI_OK)
{
for (i=0; i<16; i++) //Write 16 bytes data into FIFO
{
buff[i] = *(writeData+i);
}
CalulateCRC(buff, 16, &buff[16]);
status = MFRC522_ToCard(PCD_TRANSCEIVE, buff, 18, buff, &recvBits);if ((status != MI_OK) || (recvBits != 4) || ((buff[0] & 0x0F) != 0x0A))
{
status = MI_ERR;
}
}return status;
}
/*
* Function：MFRC522_Halt
* Description：Command the cards into sleep mode
* Input parameters：null
* return：null
*/
void MFRC522_Halt(void)
{
uchar status;
uint unLen;
uchar buff[4];buff[0] = PICC_HALT;
buff[1] = 0;
CalulateCRC(buff, 2, &buff[2]);status = MFRC522_ToCard(PCD_TRANSCEIVE, buff, 4, buff,&unLen);
}
5,334 total views, 2 views today
